+86 15516432285

sag mill vs ball mill

sag mill vs ball mill

What's the Difference Between SAG Mill and Ball Mill ...

2019-11-26 · The biggest characteristic of the sag mill is that the crushing ratio is large. The particle size of the materials to be ground is 300 ~ 400mm, sometimes even larger, and the minimum particle size of the materials to be discharged can reach 0.1 mm. The calculation shows that the crushing ratio can reach 3000 ~ 4000, while the ball mill’s ...

Read More
Difference Between Sag Mill vs Ball Mill - mech4study

2017-10-12 · 1. SAG mill is the primary tool for grinding. SAG mill is used before the other mills. Ball mill is a secondary, and it is used after the SAG mill. 2. SAG mill breaks the raw material into pieces for the further grinding. Ball mill is used

Read More
What is the difference between a SAG mill and ball mill?

SAG is an acronym for semi-autogenous grinding. SAG mills are autogenous mills that also use grinding balls like a ball mill. A SAG mill is usually a primary or first stage grinder. SAG mills use a ball charge of 8 to 21%. [6] [7] The largest SAG mill is 42′ (12.8m) in diameter, powered by a 28 MW (38,000 HP) motor. [8] A SAG mill with a 44 ...

Read More
What’s the difference of Ball mill, SAG mill, AG mill?

2018-1-11 · Attrition mill is a type of grinding mill by kinds of media to crush lump to powder-like substances. The impact can be rock on rock such as in an Autogenous Grinding (AG) mill, rock and a small ball charge (~10%), used in Semi Autogenous Grinding (SAG) mills, balls of various sizes in Ball Mills and less commonly these days, steel rods in Rod Mills.

Read More
SAG mill VS Ball & Rod Mill - Crushing, Screening ...

2021-11-20 · The pairing mill combination of a SAG/Ball mill is common in copper/gold mines for that reason. This combination can aim for a fine product sizes are around typically 100-200 micron whereas a Vertimill or ISAMill are finer at 20-40 micron or smaller.

Read More
SAG Mill Grinding Circuit Design - 911metallurgist

2016-6-6 · SAG Mill vs Ball Mill. Ball Motion inside a SAG Mill. Ball Motion inside a Ball Mill. To a more significant degree than in other comminution devices, liner

Read More
(PDF) A comparison of wear rates of ball mill grinding media

abrasive and impact wear due to their large. (75 – 100 mm) dia meters. Ball mill balls. experience a greater number of impacts, but at. lower magnitude than

Read More
Energy and Cost Comparisons of HPGR-based Circuits | E

2020-4-8 · The results showed that the HPGR-ball mill circuit achieved a 21% reduction in energy consumption over the existing SAG-ball mill circuit at the same P80 grind size of 160 mircons (μm). At a grind of 80% passing 75 μm, the

Read More
What are the differences between ball mill and rod mill ...

2021-3-8 · Ball mill and rod mill are suitable for different materials. 1. Selection by material's hardness. Ball mill has a strong adaptation of material, and it is suitable for grinding hard materials, such as slag, iron ore, copper ore, etc. Rod mill is suitable for grinding brittle material, such as rare metals. 2.

Read More
Production Engineering Archives - Page 2 of 10 -

Difference Between Sag Mill vs Ball Mill. October 12, 2017 February 22, 2018 Admin 1 Comment Manufacturing, Mill. Today we will learn about difference between sag mill vs ball mill. A mill is a machine by which solid. Read more.

Read More
Mill drives: the desire for increased power and the ...

2021-11-4 · a “SAG Mill limiting” condition, i.e., harder ore, or a “Ball Mill limiting” condition, i.e., softer ore exists. For example, a ratio of 1:1.5 or up to 1:2 would indicate a trend away from processing harder ore types and an increasing bias toward processing softer ore types, whereas a ratio of 1:1 or higher would indicate a bias

Read More
Key considerations when selecting a mill lining system

2020-1-27 · SAG mills generate higher levels of impact reduction and ball mills higher levels of abrading action. A mill lining system serves two purposes: to protect the mill shell from wear caused by the impact and abrasion of the mill charge, and to elevate and tumble the mill contents in the necessary manner to create a grinding action.

Read More
SAG Mill | Autogenous and Semi-Autogenous Mills |

Since the early 1980s, we have been designing and manufacturing Semi Autogenous Mill (SAG Mill) and Autogenous Mill (AG Mill) under the Fuller-Traylor brand. Semi-autogenous grinding uses a minimal ball charge in the range of 6

Read More
Energy and Cost Comparisons of HPGR-based Circuits | E

2020-4-8 · The results showed that the HPGR-ball mill circuit achieved a 21% reduction in energy consumption over the existing SAG-ball mill circuit at the same P80 grind size of 160 mircons (μm). At a grind of 80% passing 75 μm, the

Read More
Modelling: Transfer size limits - SAGMILLING.COM

2020-3-22 · For example, the SAG mill may have 10 MW of power draw available and the two ball mills each of 7.5 MW of power draw available for a total of ratio of 10:15 (1:1.5). The software uses the particular power model (Bond/Barratt, Morrell Mi, etc.) to determine what is the transfer size where the ratio of E SAG to E ball matches the ratio of mill ...

Read More
What are the differences between ball mill and rod mill ...

2021-3-8 · Ball mill and rod mill are suitable for different materials. 1. Selection by material's hardness. Ball mill has a strong adaptation of material, and it is suitable for grinding hard materials, such as slag, iron ore, copper ore, etc. Rod mill is suitable for grinding brittle material, such as rare metals. 2.

Read More
Optimization and Performance of Grinding Circuits: The ...

the primary crusher performance and proper control of the ratios for the SAG mill feeders drawing the ore from the stockpile. The ball mill grinding efficiency was poor and could be indicated by the fraction 400 µm in the mill discharge. This was deemed due

Read More
TECHNICAL NOTES 8 GRINDING R. P. King

2009-7-30 · LG A mill power equation for SAG mills. Minerals and Metallurgical Processing. Feb 1990 pp57-62. Gross power No load power Net power drawn by the charge (8.13) The net power is calculated from Net power KD2.5L e! c./ Watts (8.14) In equation 8.14, D is the diameter inside the mill liners and Le is the effective length of the mill including the ...

Read More
How the Modern SER Drive boosts grinding performance |

The CSE Uniserve Modern SER Drive is a compact, powerful, multi-functional and reliable addition to other SAG mill control technologies on the market today. Electrical features. The CSE Uniserve Modern SER is designed, manufactured

Read More
Home – COMESA

SAG vs Ball Mills It's important to point out that in a SAG mill, the crushing load is composed of two components; the mineral rocks and the iron balls. Thus the mineral type affects SAG mills more than ball mills.

Read More
Mill drives: the desire for increased power and the ...

2021-11-4 · a “SAG Mill limiting” condition, i.e., harder ore, or a “Ball Mill limiting” condition, i.e., softer ore exists. For example, a ratio of 1:1.5 or up to 1:2 would indicate a trend away from processing harder ore types and an increasing bias toward processing softer ore types, whereas a ratio of 1:1 or higher would indicate a bias

Read More
SAG Mill | Autogenous and Semi-Autogenous Mills |

Since the early 1980s, we have been designing and manufacturing Semi Autogenous Mill (SAG Mill) and Autogenous Mill (AG Mill) under the Fuller-Traylor brand. Semi-autogenous grinding uses a minimal ball charge in the range of 6

Read More
Autogenous and Semi-Autogenous Mills - ScienceDirect

2016-1-1 · The SAG mill had a 6–8% ball charge and the power consumption was 8 kWh/t, which agreed well with the expected value. 9.6. Problems. 9.1. In an SAG mill the dimensions of the mill were 9.75 m × 3.5 m and the specific gravities of the mineral and that of the balls charged were 4.1 and 7.9, respectively.

Read More
Energy Use of Fine Grinding in Mineral Processing

2017-8-26 · AG or SAG mill, intermediate grinding to a ball mill or tower mill, and fine grinding to a stirred mill such as an Isamill or Stirred Media Detritor (SMD). Of course, various exceptions to these typical values can be found. In fine grinding, a material with an F80 of less than 100 lm is comminuted to a P80 of 7 to 30 lm. (P80s of

Read More
The engineering and process effects of choosing a motor ...

2021-10-5 · The paper specifically describes SAG mills, but the equa-tions and principles apply equally to any conventional tumbling mill, such as AG, ball or rod mills. The engineering and process effects of choosing a motor design speed. 3 Motor electro-mechnical characteristics The cost of a motor of a Gearless Mill Drive depends mainly

Read More
Energy Benchmarking - SMC Testing

2021-11-19 · A number of samples were taken from the SAG mill feed belt and subjected to SMC Tests and Bond ball mill work index tests. Note that the Bond tests were conducted using 150 microns as the closing screen size so that the final product size from the tests was similar to the 106 microns measured during the survey.

Read More
What are the differences between ball mill and rod mill ...

2021-3-8 · Ball mill and rod mill are suitable for different materials. 1. Selection by material's hardness. Ball mill has a strong adaptation of material, and it is suitable for grinding hard materials, such as slag, iron ore, copper ore, etc. Rod mill is suitable for grinding brittle material, such as rare metals. 2.

Read More
Optimization and Performance of Grinding Circuits: The ...

the primary crusher performance and proper control of the ratios for the SAG mill feeders drawing the ore from the stockpile. The ball mill grinding efficiency was poor and could be indicated by the fraction 400 µm in the mill discharge. This was deemed due

Read More
TECHNICAL NOTES 8 GRINDING R. P. King

2009-7-30 · LG A mill power equation for SAG mills. Minerals and Metallurgical Processing. Feb 1990 pp57-62. Gross power No load power Net power drawn by the charge (8.13) The net power is calculated from Net power KD2.5L e! c./ Watts (8.14) In equation 8.14, D is the diameter inside the mill liners and Le is the effective length of the mill including the ...

Read More